* no puck in the gun, 150 M Ohm processing resistor, 39.2 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * turned on to 250 witho...
EMS Usage Instructions * The EMS data acquisition board has two ADC inputs. You can read the instantaneous value of the first ADC from PV: IBLEMS01_adc0. Yo...
* to look at L0 PV list, website: erd102:4610, look under 'groups' * soft iocs are located on erp31 * erp21 and erp22 are the linux machines in the contro...
ERL General Meeting Minutes 2009 Meeting held every Thursday at 2pm in the CHESS conference room. January 2009 * Jan 21 2009: Meeting Notes January 21 Februa...
Gun HV Processing Rules 1. The number one rule is to follow the rules below 1. Set up the following diagnostics before beginning, or make sure they are work...
* no puck in the gun, 150 M Ohm processing resistor, 39.2 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * turned on to 250 witho...
* no puck in the gun, 150 M Ohm processing resistor, 39.2 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * turned on to 250 witho...
* There is no puck in the gun yet. The original CPI insulator is in place * initial vacuum level is 9x10 12 Torr, the EPICS readout is 1.2x10 12 Torr (some of...
* no cathode puck in place, 150 M Ohm processing resistor, 40 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * nothing unusual se...
* no cathode puck in place, 150 M Ohm processing resistor, 40 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * nothing unusual se...
* copper cathode puck in place, 150 M Ohm processing resistor, 39.2 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * nothing unus...
* copper cathode puck in place, 150 M Ohm processing resistor, 39.2 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * nothing unus...
* copper cathode puck in place, 150 M Ohm processing resistor, 39.2 psi SF6 pressure * only increasing voltage after ~ 2minutes of inactivity * nothing unus...
ERL L0 Call List * L0 Operations Calendar * L0 Experimental Program * L0 List of Hardware/Software Problems and Things To Do by System * ERL L0 E Lo...
Calendar To access/modify this calendar use google account username: erlopr password: beam4all Agendas and minutes for past upcoming meetings can be found in Me...
ERL L0 List of Projects Volunteers needed Below is a list of pending projects for ERL phase 1A and 1B (ERL phase 2 can also be added), color coded as follows: P...
ERL L0 List of Hardware/Software Problems and Things To Do by System L0 Operations Calendar L0 Experimental Program L0 Standard Operating Procedures ERL L0 E L...
Phase Measurements using BPM's * Matlab script /nfs/erl/erp/matlab/l0_phase1a/bpm/bpm_get_ip_tran.m * This returns an array, 8 columns by POCKEL_CELL_RATE...
Laser Rejection Ratio Measurement and Correction * This procedure is for improving the rejection ratio, not for aligning the PC from scratch. * Requirements...
ERL L0 Standard Operating Procedures L0 Operations Calendar L0 Experimental Program L0 List of Hardware/Software Problems and Things To Do by System ERL L0 E L...
Room 128 Schedule for the week of March 5, 2007 * Monday * Morning: debugging prep system (Yulin, Brent, Bruce) * Afternoon: Laser setup and emittan...