Once David Rubin provides a gain calibration file to update BPM gains, use the ln command to create a symbolic linkfirst use the mv command like this:mv gain_cal_...
Would you like to apply the gain mapping corrections from the file ./gain_cal_mapping.in to existing parameters for all instruments COMMON to the master paramet...
Copying and transferring structure set... Post function loop... Instrument heartbeat: OK! Timing integrity : GOOD Turns seen: 39013 INFO 07/28/14 15...
Timing setup is presently: 5 14ns_FIX_G ******************************************** This mirrors all block A timing values into timing block B for efficien...
********************************************** This mirrors all block A timing values into timing block B for efficiency in acqiring calibration data. The und...
Prep() function status = 0 Copying and transferring structure set... Initializing command... Executing command... Waiting for handshake completion... CMD_D...
Copying and transferring structure set... Post function loop... INFO 07/28/14 15:18:53 : = DUMP RAW DATA Command Status Summary = Instrument Location ...
Timing setup is presently: 5 14ns_FIX_G ******************************************************* This shifts the waveform sample point on BLOCK A and B for a...
Sequence type encountered with 4 steps. *********************************************************** Install Turn By Turn Bunch = Multibunch Turn By Turn Data A...
INFO cbi_cesr_interface: CBPM CONTROL INTERFACE ACTIVE INFO 07/28/14 15:13:38 cbi_cesr_interface: exits server mode ^C INFO cbi_cesr_interface: Exiti...
******* FIND BLOCK TURN MARKER DELAY ****** Will use cached channel delays. Checking timing setup of the first active device. Startup checks shall have ensured ...
********FIND BUNCH**************** Channel delays are being set on the instrument. Enter species POSITRONS=0, ELECTRONS=1 0 : species = (0) POSITRONS Enter num...
******* GET BETATRON PHASE ***** This will calculate the betatron phase coefficients for a single bunch of either species, and generate setup/comparison coeffic...
******* PROCESSED DATA ***** Enter species POSITRONS=0, ELECTRONS=1 0 : species = (0) POSITRONS Enter the number of each bunch you wish to examine, each foll...
Copying and transferring structure set... Initializing command... Executing command... Waiting for handshake completion... CMD_DONE (3) Post function loop...
******* RAW DATA ***** (l)oad predefined, (i)ndividual bunch selection, (r)ange of bunches Specify the bunch pattern entry method: l : input = l Avai...
Copying and transferring structure set... Initializing command... Executing command... Waiting for handshake completion... CMD_DONE (3) Post function loop....
Would you like to replace all gain tables in the existing set of parameters with those that appear in the file ./gain_cal_electronic.in and save the result to a...
Would you like install the changes present in file: /nfs/cesr/online/instr/CBPM/config/09/instrument_parameters.009780 into the master operational parameters f...
. Top Level Functions Function Name AcquireAndShowXFERData Acquire data from $CESR_OFFLINE\instr\anal\cbpmII\diag\XFER_BPM_Matlab_Data, and plot it. ...
Sequence type encountered with 6 steps. Would you like to cycle power for ALL active instruments? (y/n): n : y Turning off power to all active instruments... Wai...
Would you like to begin the flash programming process for ALL active instruments? (y/n): n : y Prep() function status = 0 Copying and transferring structure set...
Sequence type encountered with 5 steps. Skipping communication connect! Copying and transferring structure set... Post function loop... INFO 07/28/14 15:26:...
Copying and transferring structure set... Post function loop... Closing all open sockets to instruments. Resetting the Coldfire/CBInet server via XBUS for instru...
Would you like to save the pedestal tables to an intermediate file? (y/n): n : y MailboxID = 0 Saving pedestal tables to intermediate file: /nfs/cesr/online/ins...
Would you like to save the timing parameters to an intermediate file? (y/n): n : y MailboxID = 0 Saving timing parameters to intermediate file: /nfs/cesr/online...
Enter timing block to scrub block A = 0, block B = 1 : Prep() function status = 0 Copying and transferring structure set... Post function loop... TIMING setu...
********* SET GAIN ************* All channels will be set to the same gain. Enter a gain setting index between 1 and 10 inclusive 4 : Prep() function status =...
Ensure there is no beam in CESR On first the West, then the East: 1 ACQUIRE PEDESTAL(19) 1 SAVE PEDESTAL PARAMETERS(10) 1 INSTALL UPDATED PARAMETERS(23) ...
******* TEST RAW DATA ******** Enter value to use for scrubbing 123 : Prep() function status = 0 Copying and transferring structure set... Initializing comm...
Prep() function status = 0 Copying and transferring structure set... Post function loop... INFO 07/28/14 16:28:28 : = Test Life Command Status Summary = I...
Sequence type encountered with 8 steps. Select the desired timing conditions: 1 = Positrons, 4nSec, timing block A Variable Gain 2 = Positrons, 4nSec, tim...
... Take Pedestals. Save and install them. Load T1B1 Positrons (14nS LDINIT), Fill to 0.75 mA, turn Separators OFF Time in 14ns_FIX_G (Block A), Save Timing...
https://cesrwww.lepp.cornell.edu/logs/Instrumentation/895 Diagnostic output from running cbic with the " h" flag: TimeScanDiagnosticsDocOutput.txt Time_Scan_Erro...
... CBIC Function tree (incomplete), might have useful info for understanding this page: https://wiki.classe.cornell.edu/ACC/Bunch/FunctionTree ... CBIC Start Cy...