Would you like to apply the gain mapping corrections from the file ./gain_cal_mapping.in to existing parameters for all instruments COMMON to the master paramet...
BPM Detector Issues #BrokenBPM1W Ongoing issues with BPM 1W (Nov Dec 2005) BPM 1W Overview * This is a 6 button detector on the large round beampipe outside ...
Minutes for May 19, 2006 * Mike Watkins: The fitting code now works and has been used this week for machine studies involving the BSM. Have started to write so...
Minutes for March 24, 2006 * lnx180c now has 1 GBit ethernet to public side in addition to existing ethernet to CESR * /nfs/cesr/instr is a 36GB mount p...
Minutes for July 28, 2006 * Discussion on storage of measurement data (i.e. not yet analyzed): We have a 2 GB partition, which is both accessible from CESR29 a...
CBPM Beam Position Monitor Electronic Logbook Description This log book is for monitoring work done with the 1st generation bunch by bunch CBPM system. Feb...
* User requirements for instrumentation, G. Codner, 04/05/05:CBPM_REQ_050405.ppt DSP * Algorithms and Command Control * DSP main loop concepts, M. Palme...
Second Generation (CBPM II) Software * Algorithms and Command / Control * Generalized DSP Executable * DSP Test Programs * General Utilities Developm...
The datafiles are the payload of the CBPM II system and through their analysis it is intended that phenomena in the accelerator may be identified and characterize...
Prep() function status = 0 Copying and transferring structure set... Initializing command... Executing command... Waiting for handshake completion... CMD_D...
CBPM II DSP Test Program Pairs This is a list of test program pairs to be used to exercise targeted functionality in the DSP. Each test requires a custom executa...
Copying and transferring structure set... Post function loop... INFO 07/28/14 15:18:53 : = DUMP RAW DATA Command Status Summary = Instrument Location ...
Sequence type encountered with 4 steps. *********************************************************** Install Turn By Turn Bunch = Multibunch Turn By Turn Data A...
INFO cbi_cesr_interface: CBPM CONTROL INTERFACE ACTIVE INFO 07/28/14 15:13:38 cbi_cesr_interface: exits server mode ^C INFO cbi_cesr_interface: Exiti...
Making Beam Measurements with CBPM II Devices This document pertains to running programs on VMS. Each hardware type has a directory named CESR.PALMER.TS101.{XX...
The CBPM Generation I system uses a standardized client server model to facilitate the taking of measurements. The client runs as an executable image in the DSP a...
******* GET BETATRON PHASE ***** This will calculate the betatron phase coefficients for a single bunch of either species, and generate setup/comparison coeffic...
Copying and transferring structure set... Initializing command... Executing command... Waiting for handshake completion... CMD_DONE (3) Post function loop...
******* RAW DATA ***** (l)oad predefined, (i)ndividual bunch selection, (r)ange of bunches Specify the bunch pattern entry method: l : input = l Avai...
CESR Bunch Instrumentation System Documentation Introduction The following Wiki pages document the existing CESR Bunch Instrumentation System (largest number ...
Would you like to replace all gain tables in the existing set of parameters with those that appear in the file ./gain_cal_electronic.in and save the result to a...
Would you like install the changes present in file: /nfs/cesr/online/instr/CBPM/config/09/instrument_parameters.009780 into the master operational parameters f...
. Top Level Functions Function Name AcquireAndShowXFERData Acquire data from $CESR_OFFLINE\instr\anal\cbpmII\diag\XFER_BPM_Matlab_Data, and plot it. ...
RTEMS Coldfire Development Environment on the CESR Control System Overview Instrumentation in the CESR control system frequently uses the RTEMS operating system ...
Would you like to save the pedestal tables to an intermediate file? (y/n): n : y MailboxID = 0 Saving pedestal tables to intermediate file: /nfs/cesr/online/ins...
Would you like to save the timing parameters to an intermediate file? (y/n): n : y MailboxID = 0 Saving timing parameters to intermediate file: /nfs/cesr/online...
How To Setup Coldfire 1. Place the Coldfire board into DIMM slot on the I/O Board. 2. Plug the XBUS/MOXA cable, Ethernet, and Power all into the I/O Bo...
******* TEST RAW DATA ******** Enter value to use for scrubbing 123 : Prep() function status = 0 Copying and transferring structure set... Initializing comm...
Prep() function status = 0 Copying and transferring structure set... Post function loop... INFO 07/28/14 16:28:28 : = Test Life Command Status Summary = I...
Sequence type encountered with 8 steps. Select the desired timing conditions: 1 = Positrons, 4nSec, timing block A Variable Gain 2 = Positrons, 4nSec, tim...
https://cesrwww.lepp.cornell.edu/logs/Instrumentation/895 Diagnostic output from running cbic with the " h" flag: TimeScanDiagnosticsDocOutput.txt Time_Scan_Erro...
... CBIC Function tree (incomplete), might have useful info for understanding this page: https://wiki.classe.cornell.edu/ACC/Bunch/FunctionTree ... CBIC Start Cy...
CBPM II Utilities Several utilities exist to control the set up and non acquisition / preprocessing behavior of the CBPM II units. Hardware Module Related Nam...